Skip to main content

adaptec - Raid 10, Logical device are missing

I have a problem with a RAID 10, I have 4 disks on raid. A disc has just been changed (0,3). But I can not rebuild the array. Logical device are setted as "Missing".



All commands return to me the following error





/usr/StorMan# /usr/StorMan/arcconf setstate 1 device 0 3 rdyControllers found: 1
The device specified does not exist.

Command aborted.



/usr/StorMan# /usr/StorMan/arcconf getconfig 1 
Controllers found: 1

----------------------------------------------------------------------
Controller information
----------------------------------------------------------------------
   Controller Status                        : Optimal
   Channel description                      : SAS/SATA
   Controller Model                         : Adaptec 2405
   Controller Serial Number                 : 2D2711FE327
   Physical Slot                            : 16
   Temperature                              : 68 C/ 154 F (Normal)
   Installed memory                         : 128 MB

   Copyback                                 : Disabled
   Background consistency check             : Disabled
   Automatic Failover                       : Enabled
   Global task priority                     : High
   Performance Mode                         : Default/Dynamic
   Stayawake period                         : Disabled
   Spinup limit internal drives             : 0
   Spinup limit external drives             : 0
   Defunct disk drive count                 : 0
   Logical devices/Failed/Degraded          : 1/0/1

   SSDs assigned to MaxIQ Cache pool        : 0
   Maximum SSDs allowed in MaxIQ Cache pool : 8
   MaxIQ Read Cache Pool Size               : 0.000 GB
   MaxIQ cache fetch rate                   : 0
   MaxIQ Cache Read, Write Balance Factor   : 3,1
   NCQ status                               : Enabled
   Statistics data collection mode          : Enabled
   --------------------------------------------------------
   Controller Version Information
   --------------------------------------------------------

   BIOS                                     : 5.2-0 (18937)
   Firmware                                 : 5.2-0 (18937)
   Driver                                   : 1.1-7 (28000)
   Boot Flash                               : 5.2-0 (18937)

----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical device number 0
   Logical device name                      : 

   RAID level                               : 10
   Status of logical device                 : Degraded
   Size                                     : 3809270 MB
   Stripe-unit size                         : 256 KB
   Read-cache mode                          : Enabled
   MaxIQ preferred cache setting            : Enabled
   MaxIQ cache setting                      : Disabled
   Write-cache mode                         : Enabled (write-back)
   Write-cache setting                      : Enabled (write-back)
   Partitioned                              : Yes

   Protected by Hot-Spare                   : No
   Bootable                                 : Yes
   Failed stripes                           : Yes
   Power settings                           : Disabled
   --------------------------------------------------------
   Logical device segment information
   --------------------------------------------------------
   Group 0, Segment 0                       : Present (0,1)             W1F20KQ9
   Group 0, Segment 1                       : Present (0,0)             Z34063KS
   Group 1, Segment 0                       : Present (0,2)             W1E2PW1C

   Group 1, Segment 1                       : Missing


----------------------------------------------------------------------
Physical Device information
----------------------------------------------------------------------
      Device #0
         Device is a Hard drive
         State                              : Online
         Supported                          : Yes

         Transfer Speed                     : SATA 3.0 Gb/s
         Reported Channel,Device(T:L)       : 0,0(0:0)
         Reported Location                  : Connector 0, Device 0
         Vendor                             : 
         Model                              : ST2000DM001-1CH1
         Firmware                           : CC24
         Serial number                      : Z34063KS
         Size                               : 1907729 MB
         Write Cache                        : Enabled (write-back)
         FRU                                : None

         S.M.A.R.T.                         : No
         S.M.A.R.T. warnings                : 0
         Power State                        : Full rpm
         Supported Power States             : Full rpm,Powered off,Reduced rpm
         SSD                                : No
         MaxIQ Cache Capable                : No
         MaxIQ Cache Assigned               : No
         NCQ status                         : Enabled
      Device #1
         Device is a Hard drive

         State                              : Online
         Supported                          : Yes
         Transfer Speed                     : SATA 3.0 Gb/s
         Reported Channel,Device(T:L)       : 0,1(1:0)
         Reported Location                  : Connector 0, Device 1
         Vendor                             : 
         Model                              : ST2000DM001-1CH1
         Firmware                           : CC24
         Serial number                      : W1F20KQ9
         Size                               : 1907729 MB

         Write Cache                        : Enabled (write-back)
         FRU                                : None
         S.M.A.R.T.                         : No
         S.M.A.R.T. warnings                : 0
         Power State                        : Full rpm
         Supported Power States             : Full rpm,Powered off,Reduced rpm
         SSD                                : No
         MaxIQ Cache Capable                : No
         MaxIQ Cache Assigned               : No
         NCQ status                         : Enabled

      Device #2
         Device is a Hard drive
         State                              : Online
         Supported                          : Yes
         Transfer Speed                     : SATA 3.0 Gb/s
         Reported Channel,Device(T:L)       : 0,2(2:0)
         Reported Location                  : Connector 0, Device 2
         Vendor                             : 
         Model                              : ST2000DM001-1CH1
         Firmware                           : CC24

         Serial number                      : W1E2PW1C
         Size                               : 1907729 MB
         Write Cache                        : Enabled (write-back)
         FRU                                : None
         S.M.A.R.T.                         : No
         S.M.A.R.T. warnings                : 0
         Power State                        : Full rpm
         Supported Power States             : Full rpm,Powered off,Reduced rpm
         SSD                                : No
         MaxIQ Cache Capable                : No

         MaxIQ Cache Assigned               : No
         NCQ status                         : Enabled


How can I start the rebuilding of the array?

Comments

Post a Comment

Popular posts from this blog

linux - Awstats - outputting stats for merged Access_logs only producing stats for one server's log

I've been attempting this for two weeks and I've accessed countless number of sites on this issue and it seems there is something I'm not getting here and I'm at a lost. I manged to figure out how to merge logs from two servers together. (Taking care to only merge the matching domains together) The logs from the first server span from 15 Dec 2012 to 8 April 2014 The logs from the second server span from 2 Mar 2014 to 9 April 2014 I was able to successfully merge them using the logresolvemerge.pl script simply enermerating each log and > out_putting_it_to_file Looking at the two logs from each server the format seems exactly the same. The problem I'm having is producing the stats page for the logs. The command I've boiled it down to is /usr/share/awstats/tools/awstats_buildstaticpages.pl -configdir=/home/User/Documents/conf/ -config=example.com awstatsprog=/usr/share/awstats/wwwroot/cgi-bin/awstats.pl dir=/home/User/Documents/parced -month=all -year=all...
Post a Comment
Read more

iLO 3 Firmware Update (HP Proliant DL380 G7)

The iLO web interface allows me to upload a .bin file ( Obtain the firmware image (.bin) file from the Online ROM Flash Component for HP Integrated Lights-Out. ) The iLO web interface redirects me to a page in the HP support website ( http://www.hp.com/go/iLO ) where I am supposed to find this .bin firmware, but no luck for me. The support website is a mess and very slow, badly categorized and generally unusable. Where can I find this .bin file? The only related link I am able to find asks me about my server operating system (what does this have to do with the iLO?!) and lets me download an .iso with no .bin file And also a related question: what is the latest iLO 3 version? (for Proliant DL380 G7, not sure if the iLO is tied to the server model)
Post a Comment
Read more

hp proliant - Smart Array P822 with HBA Mode?

We get an HP DL360 G8 with an Smart Array P822 controller. On that controller will come a HP StorageWorks D2700 . Does anybody know, that it is possible to run the Smart Array P822 in HBA mode? I found only information about the P410i, who can run HBA. If this is not supported, what you think about the LSI 9207-8e controller? Will this fit good in that setup? The Hardware we get is used but all original from HP. The StorageWorks has 25 x 900 GB SAS 10K disks. Because the disks are not new I would like to use only 22 for raid6, and the rest for spare (I need to see if the disk count is optimal or not for zfs). It would be nice if I'm not stick to SAS in future. As OS I would like to install debian stretch with zfs 0.71 as file system and software raid. I have see that hp has an page for debian to. I would like to use hba mode because it is recommend, that zfs know at most as possible about the disk, and I'm independent from the raid controller. For us zfs have many benefits, ...
Post a Comment
Read more