Skip to main content

networking - Static virtual IP in debian 6.0.4

In debian 6.0.4 my static ip is 192.168.1.151 and I want to add one more ip 192.168.1.175 as virtual ip. For did I made following changes in /etc/networking/interfaces 



# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback


# The primary network interface
allow-hotplug eth0
#NetworkManager#iface eth0 inet dhcp

auto eth0

    iface eth0 inet static
        address 192.168.1.151
        gateway 192.168.1.1

        netmask 255.255.255.0
        network 192.168.1.0
        broadcast 192.168.1.255

auto eth0:0
    iface eth0:0 inet static
        address 192.168.1.175
        netmask 255.255.255.0
        broadcast 192.168.1.255
        gateway 192.168.1.1



And when I run command 

/sbin/ifconfig -a

I get the below information

eth0      Link encap:Ethernet  HWaddr 44:87:fc:eb:b2:50  
          inet addr:192.168.1.151  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::4687:fcff:feeb:b250/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:338433 errors:0 dropped:0 overruns:0 frame:0
          TX packets:238153 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 
          RX bytes:337480876 (321.8 MiB)  TX bytes:68577550 (65.4 MiB)
          Interrupt:25 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:3735 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3735 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 
          RX bytes:494269 (482.6 KiB)  TX bytes:494269 (482.6 KiB)

pan0      Link encap:Ethernet  HWaddr 16:56:67:bf:36:84  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)



Mostly I get this but some time i get the virtual ip in the output. I have to make virtual ip permanent. How can i do that? Also I will assign this virtual ip (192.168.1.175) to two machine.



Thanks

Comments

Post a Comment

Popular posts from this blog

linux - iDRAC6 Virtual Media native library cannot be loaded

When attempting to mount Virtual Media on a iDRAC6 IP KVM session I get the following error: I'm using Ubuntu 9.04 and: $ javaws -version Java(TM) Web Start 1.6.0_16 $ uname -a Linux aud22419-linux 2.6.28-15-generic #51-Ubuntu SMP Mon Aug 31 13:39:06 UTC 2009 x86_64 GNU/Linux $ firefox -version Mozilla Firefox 3.0.14, Copyright (c) 1998 - 2009 mozilla.org On Windows + IE it (unsurprisingly) works. I've just gotten off the phone with the Dell tech support and I was told it is known to work on Linux + Firefox, albeit Ubuntu is not supported (by Dell, that is). Has anyone out there managed to mount virtual media in the same scenario?
Post a Comment
Read more

hp proliant - Smart Array P822 with HBA Mode?

We get an HP DL360 G8 with an Smart Array P822 controller. On that controller will come a HP StorageWorks D2700 . Does anybody know, that it is possible to run the Smart Array P822 in HBA mode? I found only information about the P410i, who can run HBA. If this is not supported, what you think about the LSI 9207-8e controller? Will this fit good in that setup? The Hardware we get is used but all original from HP. The StorageWorks has 25 x 900 GB SAS 10K disks. Because the disks are not new I would like to use only 22 for raid6, and the rest for spare (I need to see if the disk count is optimal or not for zfs). It would be nice if I'm not stick to SAS in future. As OS I would like to install debian stretch with zfs 0.71 as file system and software raid. I have see that hp has an page for debian to. I would like to use hba mode because it is recommend, that zfs know at most as possible about the disk, and I'm independent from the raid controller. For us zfs have many benefits, ...
Post a Comment
Read more

linux - Awstats - outputting stats for merged Access_logs only producing stats for one server's log

I've been attempting this for two weeks and I've accessed countless number of sites on this issue and it seems there is something I'm not getting here and I'm at a lost. I manged to figure out how to merge logs from two servers together. (Taking care to only merge the matching domains together) The logs from the first server span from 15 Dec 2012 to 8 April 2014 The logs from the second server span from 2 Mar 2014 to 9 April 2014 I was able to successfully merge them using the logresolvemerge.pl script simply enermerating each log and > out_putting_it_to_file Looking at the two logs from each server the format seems exactly the same. The problem I'm having is producing the stats page for the logs. The command I've boiled it down to is /usr/share/awstats/tools/awstats_buildstaticpages.pl -configdir=/home/User/Documents/conf/ -config=example.com awstatsprog=/usr/share/awstats/wwwroot/cgi-bin/awstats.pl dir=/home/User/Documents/parced -month=all -year=all...
Post a Comment
Read more